Is it good to coat in Oklahoma City, OK this week?
A live 7-day go/no-go calendar for epoxy & resin floors in Oklahoma City, built from the local forecast against the 5°F-above-dew-point rule. We lead with the signal a weather app misses: overnight condensation risk.
- Dew margin
- 0.5°F
- Overnight dew
- High
- Rain
- 26%
- Window
- —
High condensation risk overnight — surface dips to within 0.5°F of the 67°F dew point (low 65°F, 100% cloud, 7 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.
- Dew margin
- 2.6°F
- Overnight dew
- Watch
- Rain
- 19%
- Window
- —
Humidity peaks at 96% — well above the 85% ceiling; cure stalls and moisture gets trapped.
- Dew margin
- -2.2°F
- Overnight dew
- High
- Rain
- 11%
- Window
- —
High condensation risk overnight — surface dips to within -2.2°F of the 62°F dew point (low 60°F, 0% cloud, 7 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.
- Dew margin
- -2.5°F
- Overnight dew
- High
- Rain
- 2%
- Window
- —
High condensation risk overnight — surface dips to within -2.5°F of the 58°F dew point (low 56°F, 0% cloud, 8 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.
- Dew margin
- -2.6°F
- Overnight dew
- High
- Rain
- 0%
- Window
- —
High condensation risk overnight — surface dips to within -2.6°F of the 54°F dew point (low 51°F, 0% cloud, 7 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.
- Dew margin
- 4°F
- Overnight dew
- Watch
- Rain
- 0%
- Window
- 8am–5pm
Watch overnight dew — surface comes within 4°F of the dew point (margin is 5°F). Time the coat to dry well before evening.
- Dew margin
- 10.5°F
- Overnight dew
- Low
- Rain
- 1%
- Window
- 8am–5pm
Hot afternoon (86°F, ceiling 86°F) — coat early and follow the shade.
- High condensation risk overnight — surface dips to within 0.5°F of the 67°F dew point (low 65°F, 100% cloud, 7 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.
- Rain likely in the 24h cure window (26% chance, ~5.4mm) — it can wash out or mar an uncured coat.
- High humidity (95%, over the 85% mark) slows drying — keep an eye on the cure window.
Hold off. These are forecast numbers — confirm the surface temperature on-site before you start.
Why these thresholds
Installing within 5°F of the dew point causes amine blush / carbamation — a cloudy, greasy, hazed floor. The slab surface temp, not the air, is what counts.
- • Surface temp must stay 5°F above the dew point through application and cure (ASTM D3276 / ISO 8502-42).
- • Air + surface in the 50–86°F band (low-temp lines to 50°F).
- • Humidity under 85%; ideally under 80%.
- • No rain for 24h after application.
- • We use the forecast ground-surface temperature as a surface-temp proxy — confirm on-site with an IR thermometer.
Free in the beta
Watch this job site 24/7
Get an email the moment overnight dew, rain, or an out-of-range stretch threatens a fresh coat — and a morning digest with the best window ahead. No app to check; we watch the forecast for you.