paint·day

Is it good to coat in Scottsdale, AZ this week?

A live 7-day go/no-go calendar for epoxy & resin floors in Scottsdale, built from the local forecast against the 5°F-above-dew-point rule. We lead with the signal a weather app misses: overnight condensation risk.

TodayCautionBest upcoming window: Thu (Good to go)
MonCAUTION
79°/58°
Dew margin
3.9°F
Overnight dew
Watch
Rain
54%
Window
8am–5pm

Watch overnight dew — surface comes within 3.9°F of the dew point (margin is 5°F). Time the coat to dry well before evening.

TueRISK
68°/62°
Dew margin
4°F
Overnight dew
High
Rain
45%
Window
—

High condensation risk overnight — surface dips to within 4°F of the 44°F dew point (low 47°F, 3% cloud, 2 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.

WedCAUTION
69°/49°
Dew margin
10.1°F
Overnight dew
Low
Rain
0%
Window
9am–5pm

Cold mornings (down to 49°F, floor is 50°F) — wait for the surface to warm past midday before you coat.

ThuGO
73°/61°
Dew margin
12.7°F
Overnight dew
Low
Rain
4%
Window
8am–5pm

Clear to coat: temps 61–73°F, RH under 42%, surface stays 12.7°F+ above the dew point, no rain in the cure window.

FriGO
69°/62°
Dew margin
6.7°F
Overnight dew
Low
Rain
4%
Window
8am–5pm

Clear to coat: temps 62–69°F, RH under 38%, surface stays 6.7°F+ above the dew point, no rain in the cure window.

SatGO
68°/61°
Dew margin
5.2°F
Overnight dew
Low
Rain
0%
Window
8am–5pm

Clear to coat: temps 61–68°F, RH under 48%, surface stays 5.2°F+ above the dew point, no rain in the cure window.

SunGO
71°/60°
Dew margin
6.1°F
Overnight dew
Low
Rain
1%
Window
8am–5pm

Clear to coat: temps 60–71°F, RH under 45%, surface stays 6.1°F+ above the dew point, no rain in the cure window.

CautionMon — today & tonight
  • Watch overnight dew — surface comes within 3.9°F of the dew point (margin is 5°F). Time the coat to dry well before evening.
  • Some rain risk (54%) during the cure window — re-check the radar before you start.

Caution. These are forecast numbers — confirm the surface temperature on-site before you start.

Why these thresholds

Installing within 5°F of the dew point causes amine blush / carbamation — a cloudy, greasy, hazed floor. The slab surface temp, not the air, is what counts.

  • • Surface temp must stay 5°F above the dew point through application and cure (ASTM D3276 / ISO 8502-42).
  • • Air + surface in the 50–86°F band (low-temp lines to 50°F).
  • • Humidity under 85%; ideally under 80%.
  • • No rain for 24h after application.
  • • We use the forecast ground-surface temperature as a surface-temp proxy — confirm on-site with an IR thermometer.

Free in the beta

Watch this job site 24/7

Get an email the moment overnight dew, rain, or an out-of-range stretch threatens a fresh coat — and a morning digest with the best window ahead. No app to check; we watch the forecast for you.

Set up a free alert→

Other coatings in Scottsdale

Epoxy & Resin Floors weather elsewhere in Arizona