paint·day

Is it good to coat in St. Petersburg, FL this week?

A live 7-day go/no-go calendar for epoxy & resin floors in St. Petersburg, built from the local forecast against the 5°F-above-dew-point rule. We lead with the signal a weather app misses: overnight condensation risk.

TodayHold offBest upcoming window: Mon (Good to go)
TueRISK
66°/64°
Dew margin
2.4°F
Overnight dew
Watch
Rain
75%
Window
—

Rain likely in the 24h cure window (75% chance, ~12.3mm) — it can wash out or mar an uncured coat.

WedRISK
73°/66°
Dew margin
2.1°F
Overnight dew
Watch
Rain
35%
Window
—

Rain likely in the 24h cure window (35% chance, ~17.6mm) — it can wash out or mar an uncured coat.

ThuRISK
80°/69°
Dew margin
3.1°F
Overnight dew
Watch
Rain
28%
Window
—

Rain likely in the 24h cure window (28% chance, ~4.6mm) — it can wash out or mar an uncured coat.

FriRISK
73°/70°
Dew margin
1.5°F
Overnight dew
High
Rain
30%
Window
—

High condensation risk overnight — surface dips to within 1.5°F of the 69°F dew point (low 68°F, 100% cloud, 19 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.

SatCAUTION
77°/68°
Dew margin
2.9°F
Overnight dew
Watch
Rain
13%
Window
10am–5pm

Watch overnight dew — surface comes within 2.9°F of the dew point (margin is 5°F). Time the coat to dry well before evening.

SunRISK
76°/69°
Dew margin
2.1°F
Overnight dew
High
Rain
6%
Window
—

High condensation risk overnight — surface dips to within 2.1°F of the 63°F dew point (low 65°F, 17% cloud, 7 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.

MonGO
75°/69°
Dew margin
9.4°F
Overnight dew
Low
Rain
8%
Window
9am–5pm

Clear to coat: temps 69–75°F, RH under 81%, surface stays 9.4°F+ above the dew point, no rain in the cure window.

Hold offTue — today & tonight
  • Rain likely in the 24h cure window (75% chance, ~12.3mm) — it can wash out or mar an uncured coat.
  • Watch overnight dew — surface comes within 2.4°F of the dew point (margin is 5°F). Time the coat to dry well before evening.
  • High humidity (93%, over the 85% mark) slows drying — keep an eye on the cure window.

Hold off. These are forecast numbers — confirm the surface temperature on-site before you start.

Why these thresholds

Installing within 5°F of the dew point causes amine blush / carbamation — a cloudy, greasy, hazed floor. The slab surface temp, not the air, is what counts.

  • • Surface temp must stay 5°F above the dew point through application and cure (ASTM D3276 / ISO 8502-42).
  • • Air + surface in the 50–86°F band (low-temp lines to 50°F).
  • • Humidity under 85%; ideally under 80%.
  • • No rain for 24h after application.
  • • We use the forecast ground-surface temperature as a surface-temp proxy — confirm on-site with an IR thermometer.

Free in the beta

Watch this job site 24/7

Get an email the moment overnight dew, rain, or an out-of-range stretch threatens a fresh coat — and a morning digest with the best window ahead. No app to check; we watch the forecast for you.

Set up a free alert→

Other coatings in St. Petersburg

Epoxy & Resin Floors weather elsewhere in Florida