paint·day

Is it good to coat in Tacoma, WA this week?

A live 7-day go/no-go calendar for epoxy & resin floors in Tacoma, built from the local forecast against the 5°F-above-dew-point rule. We lead with the signal a weather app misses: overnight condensation risk.

TodayCautionBest upcoming window: Sun (Caution)
SunCAUTION
55°/47°
Dew margin
4.6°F
Overnight dew
Watch
Rain
44%
Window
10am–12pm

Watch overnight dew — surface comes within 4.6°F of the dew point (margin is 5°F). Time the coat to dry well before evening.

MonRISK
50°/42°
Dew margin
3.5°F
Overnight dew
High
Rain
13%
Window
—

High condensation risk overnight — surface dips to within 3.5°F of the 38°F dew point (low 38°F, 14% cloud, 5 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.

TueRISK
51°/39°
Dew margin
1.2°F
Overnight dew
High
Rain
11%
Window
—

High condensation risk overnight — surface dips to within 1.2°F of the 36°F dew point (low 38°F, 5% cloud, 4 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.

WedRISK
50°/41°
Dew margin
2.2°F
Overnight dew
Watch
Rain
32%
Window
—

Too cold to coat — daytime high only 50°F, below the 50°F minimum (even a low-temp line needs 50°F+).

ThuRISK
50°/41°
Dew margin
4.4°F
Overnight dew
Watch
Rain
3%
Window
—

Too cold to coat — daytime high only 50°F, below the 50°F minimum (even a low-temp line needs 50°F+).

FriRISK
47°/37°
Dew margin
4.5°F
Overnight dew
Watch
Rain
19%
Window
—

Too cold to coat — daytime high only 47°F, below the 50°F minimum (even a low-temp line needs 50°F+).

SatRISK
44°/41°
Dew margin
-3.5°F
Overnight dew
High
Rain
25%
Window
—

High condensation risk overnight — surface dips to within -3.5°F of the 38°F dew point (low 35°F, 100% cloud, 10 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.

CautionSun — today & tonight
  • Watch overnight dew — surface comes within 4.6°F of the dew point (margin is 5°F). Time the coat to dry well before evening.
  • Cold mornings (down to 47°F, floor is 50°F) — wait for the surface to warm past midday before you coat.
  • High humidity (91%, over the 85% mark) slows drying — keep an eye on the cure window.
  • Some rain risk (44%) during the cure window — re-check the radar before you start.

Caution. These are forecast numbers — confirm the surface temperature on-site before you start.

Why these thresholds

Installing within 5°F of the dew point causes amine blush / carbamation — a cloudy, greasy, hazed floor. The slab surface temp, not the air, is what counts.

  • • Surface temp must stay 5°F above the dew point through application and cure (ASTM D3276 / ISO 8502-42).
  • • Air + surface in the 50–86°F band (low-temp lines to 50°F).
  • • Humidity under 85%; ideally under 80%.
  • • No rain for 24h after application.
  • • We use the forecast ground-surface temperature as a surface-temp proxy — confirm on-site with an IR thermometer.

Free in the beta

Watch this job site 24/7

Get an email the moment overnight dew, rain, or an out-of-range stretch threatens a fresh coat — and a morning digest with the best window ahead. No app to check; we watch the forecast for you.

Set up a free alert→

Other coatings in Tacoma

Epoxy & Resin Floors weather elsewhere in Washington