paint·day

Is it good to coat in Bellevue, WA this week?

A live 7-day go/no-go calendar for epoxy & resin floors in Bellevue, built from the local forecast against the 5°F-above-dew-point rule. We lead with the signal a weather app misses: overnight condensation risk.

TodayHold offBest upcoming window: Mon (Caution)
SunRISK
55°/48°
Dew margin
4.6°F
Overnight dew
Watch
Rain
43%
Window
—

Rain likely in the 24h cure window (43% chance, ~2.5mm) — it can wash out or mar an uncured coat.

MonCAUTION
51°/42°
Dew margin
4.7°F
Overnight dew
Watch
Rain
15%
Window
2pm–5pm

Watch overnight dew — surface comes within 4.7°F of the dew point (margin is 5°F). Time the coat to dry well before evening.

TueRISK
51°/40°
Dew margin
3.3°F
Overnight dew
High
Rain
5%
Window
—

High condensation risk overnight — surface dips to within 3.3°F of the 37°F dew point (low 39°F, 5% cloud, 3 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.

WedCAUTION
50°/40°
Dew margin
5.4°F
Overnight dew
Low
Rain
24%
Window
2pm–5pm

Cold mornings (down to 40°F, floor is 50°F) — wait for the surface to warm past midday before you coat.

ThuRISK
49°/41°
Dew margin
6.5°F
Overnight dew
Low
Rain
3%
Window
—

Too cold to coat — daytime high only 49°F, below the 50°F minimum (even a low-temp line needs 50°F+).

FriRISK
48°/39°
Dew margin
7.4°F
Overnight dew
Low
Rain
18%
Window
—

Too cold to coat — daytime high only 48°F, below the 50°F minimum (even a low-temp line needs 50°F+).

SatRISK
49°/42°
Dew margin
-1.8°F
Overnight dew
High
Rain
25%
Window
—

High condensation risk overnight — surface dips to within -1.8°F of the 40°F dew point (low 38°F, 100% cloud, 10 mph wind). A fresh coat can blush/blister. Stop 4h before dew falls.

Hold offSun — today & tonight
  • Rain likely in the 24h cure window (43% chance, ~2.5mm) — it can wash out or mar an uncured coat.
  • Watch overnight dew — surface comes within 4.6°F of the dew point (margin is 5°F). Time the coat to dry well before evening.
  • Cold mornings (down to 48°F, floor is 50°F) — wait for the surface to warm past midday before you coat.
  • High humidity (91%, over the 85% mark) slows drying — keep an eye on the cure window.

Hold off. These are forecast numbers — confirm the surface temperature on-site before you start.

Why these thresholds

Installing within 5°F of the dew point causes amine blush / carbamation — a cloudy, greasy, hazed floor. The slab surface temp, not the air, is what counts.

  • • Surface temp must stay 5°F above the dew point through application and cure (ASTM D3276 / ISO 8502-42).
  • • Air + surface in the 50–86°F band (low-temp lines to 50°F).
  • • Humidity under 85%; ideally under 80%.
  • • No rain for 24h after application.
  • • We use the forecast ground-surface temperature as a surface-temp proxy — confirm on-site with an IR thermometer.

Free in the beta

Watch this job site 24/7

Get an email the moment overnight dew, rain, or an out-of-range stretch threatens a fresh coat — and a morning digest with the best window ahead. No app to check; we watch the forecast for you.

Set up a free alert→

Other coatings in Bellevue

Epoxy & Resin Floors weather elsewhere in Washington